1. Unscrew the cartridge wax:
Twist the lid of the cartridge wax counterclockwise following the thread design on the cartridge. Some cartridges may require a little more force to unscrew, it will turn however!

2. Remove the leakproof seal on the cartridge:
Gently tear off the seal to expose the wax within the cartridge.

3. Tighten the cap:
Once the seal has been removed, make sure to screw the roller cap onto the cartridge tightly, this will prevent any wax from spilling.

4. Insert the cartridge:
Insert the wax into the roller device by placing the cartridge inside.

5. Plug the device in:
Plug the device into the socket and press the power button on the front of the device, this will be red to begin with.

6. Device heating to temperature:
The light will turn from red to green when the wax has reached the correct temperature, this heating process should only take around 10 minutes.

7. Insert the cartridge:
The light will turn from red to green when the wax has reached the correct temperature, this heating process should only take around 10 minutes.

8. Keep the device plugged in until you're ready to use:
Don’t unplug the device until the next step has been completed, this ensures the wax will stay at optimum temperature for your treatment.

• Make sure your legs are clean, dry, and free of oils or moisturiser
• Lay an old towel underneath to protect surfaces from spills.
• Ensure your hands are clean too.
• Important information: Retinoids are powerful ingredients that are part of the Vitamin A family, commonly found in skincare. The use of retinoids can make skin more sensitive to waxing. If using ingredients such as Retinol, Tretinoin or anti-ageing products, we recommend to stop using these on the skin for 5-7 days before waxing to avoid grazing the skin. This product should not be used by people taking prescription retinoids.
• Once you have removed the wax strip, if any residue wax remains simply pick it up on the same wax strip, you will see us demonstrating this throughout the process.
• Before you begin waxing, once the device has reached optimal temperature, unscrew the roller head and using the reusable spatula provided, poke into the top layer of wax, this will begin the wax flow. Now attach the roller head again.

Test the Wax Temperature

• Apply a small amount of wax to the inner side of your wrist to check the temperature.
• If it feels too hot, wait a few minutes and retest. If it’s too thick and dragging this means it is too cool, plug the device back in and retest after 5 minutes.
• Remove the wax from testing by applying a wax strip on top of the wet wax, gently press down and pull off.

Each wax strip can be used for two roller sections from just below elbow to wrist, but if it starts pulling or tugging at the skin, replace the strip with a fresh one.

Move the strip to the next fresh wax area, making sure to leave 1 inch of free strip at the bottom for easy removal.

Move to the upper arm and repeat the process:

Apply wax in the direction of hair growth, starting from just below the shoulder and moving towards the elbow.

Use a new wax strip to remove the wax, pulling it against the hair growth.

To wax the back of the arm you will need to bend your arm but continue to follow the steps as above.

For the elbow or areas where hair grows in different directions, work in smaller sections and adjust the application to match the hair growth pattern.

Using the post wax wipe included in the kit wipe over the entire waxed area, this will remove any sticky residue but also soothe the freshly waxed skin. Don’t bin this yet!

1. Disassemble the Device: Unscrew the top of the device to release the roller head.

2. Remove the wax: Roll onto a clean wax strip repeatedly to remove most of the wax.

3. Soak the Roller: Place the roller head in a bowl of boiling water and let it soak for 10 minutes.

4. Remove Residue: Carefully take the roller head out of the water. Roll it onto a clean wax strip repeatedly until no residue remains.

5. Clean the Inner Sides: Use the wipe saved from soothing your legs to clean the inner edges of the roller where wax may have accumulated.

6. Reassemble: Once all the wax is removed, reattach the roller head securely onto the device.

7. Proper Storage: Store the device upright in a cool, dark room, away from direct sunlight.

By following these steps, you'll maintain your roller device in top condition and ready for use every time!